Stage 1: eyes
The eye block on its test stand: both eyes turn together, left and right on one servo and up and down on another, and each eye’s upper and lower lid close on that eye’s own servo. Four servos on the eyes Core, which stands against the stand’s back.
Parts it adds, from the model
Section titled “Parts it adds, from the model”| Part | Count | Printed in |
|---|---|---|
| bail | 1 | Joints: PETG Basic Black (30105)PETG Matte White (35100) |
| Core | 1 | bought |
| eyeball core | 2 | Joints: PETG Basic Black (30105)PETG Matte White (35100) |
| gimbal frame | 1 | Bones: PETG Basic Black (30105)PETG Basic Dark Beige (30403) |
| L eyeball cap | 1 | eye whites: PLA Pure Pure White (17100)PLA Basic Jade White (10100)PLA Matte Ivory White (11100) |
| L lower lid | 1 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| L upper lid | 1 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| lid bar | 2 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| lid link | 2 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| pitch bar | 1 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| push-rod | 2 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| R eyeball cap | 1 | eye whites: PLA Pure Pure White (17100)PLA Basic Jade White (10100)PLA Matte Ivory White (11100) |
| R lower lid | 1 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| R upper lid | 1 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| servo | 4 | bought |
| servo horn | 4 | bought |
| Shield | 1 | bought |
| test stand | 1 | Bones: PETG Basic Black (30105)PETG Basic Dark Beige (30403) |
| tie-bar | 1 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| yaw yoke | 2 | Joints: PETG Basic Black (30105)PETG Matte White (35100) |
Servos it adds
Section titled “Servos it adds”| Core | Servo | The model’s range |
|---|---|---|
| eyes | yaw | 65..115 |
| eyes | pitch | 59.6..120.6 |
| eyes | L lid | 54..105 |
| eyes | R lid | 54..105 |
The ranges are the model’s, in servo degrees, where every part sweeps clear; the real servos get calibrated (Calibration).
Assembly, as the model places it
Section titled “Assembly, as the model places it”- Gimbal frame: the eye block’s plate, carrying both eyes’ pivots and the four servos behind and between the eyes: each lid servo upright behind its eye, the yaw servo hanging under the plate.
- Yaw yokes, one per eye, turning left and right in the frame; the tie-bar joins them to the yaw servo’s horn.
- Eyeball cores turning up and down in the yokes; the bail and its two push-rods turn both from the pitch servo through the pitch bar.
- Lids: each eye’s upper lid through its lid bar from its lid servo, the lower lid through a lid link off that bar, so the two close against each other.
- Eyeball caps on the cores.
- Test stand screwed under the frame’s plate, where the head mount goes in Stage 2; the eyes Core on its Shield against the stand’s back.
Wiring
Section titled “Wiring”The four servos go to the eyes Core (Wiring); flash it (Flashing). The model’s Stage 1 carries no pack: the pack and the switch board sit beside the stand until the Torso holds them in Stage 2 (inferred).
noggin v0.2.26-6-g09bf9b7 · 09bf9b7