Stage 2: neck
The eye block leaves its test stand for the neck: the head turns left and right (pan) and nods (tilt) on its own pivots, each servo driving it through a bar. The Torso under it holds both packs and the switch board; both Cores ride in the head’s cranium. Two more servos, on the neck Core.
Parts it adds, from the model
Section titled “Parts it adds, from the model”| Part | Count | Printed in |
|---|---|---|
| battery pack | 2 | bought |
| charger dongle | 1 | bought |
| Core | 1 | bought |
| cranium tray | 1 | Mounts: PETG Basic Black (30105) |
| head mount | 1 | Bones: PETG Basic Black (30105)PETG Basic Dark Beige (30403) |
| neck mount | 1 | Bones: PETG Basic Black (30105)PETG Basic Dark Beige (30403) |
| pan bar | 1 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| pan yoke | 1 | Joints: PETG Basic Black (30105)PETG Matte White (35100) |
| servo | 2 | bought |
| servo horn | 2 | bought |
| Shield | 1 | bought |
| switch board | 1 | bought |
| tilt bar | 1 | Linkages: PETG Basic Black (30105)PETG Matte Pink (35700) |
| torso | 1 | Mounts: PETG Basic Black (30105) |
| torso lid | 1 | Mounts: PETG Basic Black (30105) |
It takes off: test stand.
Servos it adds
Section titled “Servos it adds”| Core | Servo | The model’s range |
|---|---|---|
| neck | pan | 33.9..146.5 |
| neck | tilt | 42.1..139.7 |
The ranges are the model’s, in servo degrees, where every part sweeps clear; the real servos get calibrated (Calibration).
Assembly, as the model places it
Section titled “Assembly, as the model places it”- Torso: the box pedestal the Mech stands on, the pack lying low in it, the switch board lying flat beside the pack’s lead end, its lever reached through a hole in the lid, the spare pack in front on the kit’s charger dongle, an opening in the -x wall where the two packs’ plugs swap and the dongle’s USB lead leaves, and the neck mount standing on its floor, its hollow post rising through the torso lid, the pack’s Y lead up inside it, the pan servo on its shelf over the lid. The lid slides onto the post from behind through its slot, over the walls, then drops onto its ledge inside them, flush with their top, where it cannot slide off.
- Pan yoke turning on the post’s top under the head, the tilt servo on its floor; the pan bar joins it to the pan servo’s horn.
- Head mount turning on the yoke’s cheeks, the tilt pivot under the skull’s base behind the head’s centre of mass, a torsion spring on its shank holding the head’s weight (the balance spring); the tilt bar joins it to the tilt servo’s horn.
- Eye block from Stage 1 on the head mount, in the test stand’s place.
- Cranium tray on the gimbal frame’s plate, up behind the bail: both Cores lying flat on their Shields on it, each USB-C socket’s opening straight back through the skull.
Each busy pivot is a greased M3 shank turning in a bore printed along the layers’ axis.
Wiring
Section titled “Wiring”The neck Core joins the Wi-Fi like the eyes Core (Wiring). One pack and the switch board in the Torso feed both Shields in the head, the Y lead’s one pair up the post, split in the cranium; every servo lead runs to the Shields in the head, and the leads that cross the pan and tilt pivots (the pan servo’s, the tilt servo’s and the Y lead’s pair) are clamped at both ends and bent no tighter than ten times their diameter.
noggin v0.2.26-6-g09bf9b7 · 09bf9b7